Results 1 to 6 of 6

Thread: Fuid Thin Film Coating (FTFC) – before covering ?

  1. #1
    Senior Member
    Join Date
    Feb 2020
    Location
    Varese, ITALY
    Posts
    176

    Default Fluid Thin Film Coating (FTFC) – before covering ?

    Happy New Year everybody !


    In my modest aviation culture, assembling aluminum parts without the slightest anti-corrosion protection is rather considered like an heresy. But considering all the arguments, I decided to follow CC’s manuals closely and not apply any primer before assembling the wings.

    However, I consider the application of FTCF. (“CorrosionX” in this case)

    My question:
    Are there contraindications to the application of FTCF before (and after) covering?

    Yves
    Last edited by PBY Catalina; 01-01-2021 at 02:46 PM.

  2. #2
    Junior Member
    Join Date
    Jun 2020
    Location
    Kharkiv, Ukraine
    Posts
    10

    Default Re: Fuid Thin Film Coating (FTFC) – before covering ?

    This is a great product for corrosion protection and lubrication in one bottle

  3. #3
    Senior Member
    Join Date
    Mar 2016
    Location
    Idaho
    Posts
    393

    Default Re: Fuid Thin Film Coating (FTFC) – before covering ?

    It is my understanding that CorrosionX is applied to fully metal aircraft. It is not uncommon to have older GA (Cessna, Piper, Beech,...) to have CorrosionX sprayed into the wings and fuse. Where it will drip out from the wings and fuse for many hours.

    I personally would not apply it to a soon to be fabric covered aircraft. I would be concerned it would eventually run down onto the fabric interior.

    If concerned about corrosion I would prime interior parts (adds weight, most sheet metal parts are Aclad). Extra information here: Two pack paint wings for corrosion proof before covering (supercub.org)

    When I was building an RV7 there was GREAT discussions on whether to prime or not. I could never understand why people would spend hours scuffing off the great almost pure aluminum (Aclad) corrosion protection to add prime and paint for better corrosion protection. And a ton of weight.

    I guess it comes down to personal choice.

    Considering this was Posted in January, what did you decide to do?
    Dan Arnold
    KEUL

  4. #4
    Senior Member
    Join Date
    Feb 2020
    Location
    Varese, ITALY
    Posts
    176

    Cool Re: Fuid Thin Film Coating (FTFC) – before covering ?

    Hello Dan,

    Alclad is a very thin layer of pure aluminium that is a good protection, but who do not give you any insurance that your airplane will not be rapidly invaded by corrosion.

    As a homebuilder I’m a beginner, but professionally I have been very concerned by airplane corrosion. I have seen airliners who were very badly damaged and AOG due to corrosion on painted Alclad after only 4 years of operations.

    We are drilling hundreds of little holes in our EX, each one that can be the start of future intergranular corrosion. But my future EX2 will not be used as an Airliners and will be most of the time well protected in a dry hangar. After reading many discussions about this very controversial subject, and asking the opinion of technician’s specialists in corrosion protection, I decided not to cover my airplane with primer but to use FTFC products.

    Apparently, there is no problem to use CorrosionX on fabric as long it’s not used before covering and the painting dry. I will wait one or two months after the covering and the painting before spaying the CorrosionX.



    Yves
    Last edited by PBY Catalina; 04-20-2021 at 11:28 AM.

  5. #5
    Senior Member
    Join Date
    Mar 2016
    Location
    Idaho
    Posts
    393

    Default Re: Fuid Thin Film Coating (FTFC) – before covering ?

    Thanks for the interesting update.

    Let us know how the CorrosionX application works out.

    Cheers,
    Dan
    Dan Arnold
    KEUL

  6. #6
    Senior Member David H's Avatar
    Join Date
    Aug 2012
    Location
    Rochester, Michigan
    Posts
    188

    Default Re: Fuid Thin Film Coating (FTFC) – before covering ?

    I applied CorrosionX to the inside of my EX2 fuselage frame right after unpacking the big box. I sprayed it in the open holes that are present in the bare fuselage using the thin tube supplied with the can. I made no attempt to fog it as the professionals do.
    It was dripping out months later during the fuselage assembly when I would rotate the fuselage.

    I never had any issues with covering or paint. Two years post completion and I have no bleed through on the paint (Stewart Systems). Perhaps all the rotating of the fuselage during assembly allowed my over application to drip out. It really does not take much. The liquid you spray in "crawls" along the metal for months.

    So?? A very small amount of effort for a hoped for anticorrosion benefit.
    I would definitely do it again. (but only two years out and not living near salt water is not a very definitive test). CorrosionX is an amazingly good product.

    Cheers!
    David

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •