Page 3 of 3 FirstFirst 123
Results 21 to 30 of 30

Thread: Primer Fuel Line Failure

  1. #21
    Senior Member Mark Keneston's Avatar
    Join Date
    Dec 2016
    Location
    Saratoga Springs, NY
    Posts
    463

    Default Re: Primer Fuel Line Failure

    Quote Originally Posted by seastar View Post
    I just noticed that the break in the copper tube occurred at the smallest bend radius.
    I wonder if that point were over bent or some how stressed too much?
    I can't see any damage to the tube in the picture but something caused it to break where it did.
    Maybe defective tube?
    Seastar can you send me any pictures of this, the loops, bends and clamps? Please. If there is excess tubing and limited clamps, then vibration can cause a stress fracture. As for the no start issue, where are you located? Aircraft inside or tied outside? Also is this a factory built plane or an EX kit built? How many primer ports do you have? Our FX sits in a hanger at 45-50 degrees and I can just stroke the throttle 2-3 times and it fires up.

    im trying to help just need more info please. Thanks Mark. Yankee 1
    Cub Crafters
    Factory Direct New & Used Aircraft Sales
    NorthEast & Great Lakes Region
    518.410.9404

  2. #22
    Senior Member Mark Keneston's Avatar
    Join Date
    Dec 2016
    Location
    Saratoga Springs, NY
    Posts
    463

    Default Re: Primer Fuel Line Failure

    Quote Originally Posted by Mark Keneston View Post
    Seastar can you send me any pictures of this, the loops, bends and clamps? Please. If there is excess tubing and limited clamps, then vibration can cause a stress fracture. As for the no start issue, where are you located? Aircraft inside or tied outside? Also is this a factory built plane or an EX kit built? How many primer ports do you have? Our FX sits in a hanger at 45-50 degrees and I can just stroke the throttle 2-3 times and it fires up.

    im trying to help just need more info please. Thanks Mark. Yankee 1
    Also looking at Turbo’s pictures it looks like far too much line and the loop itself did not look clamped. That vibration surely could fracture that loop. I also know many who will prime two cyls instead of just one. MK
    Cub Crafters
    Factory Direct New & Used Aircraft Sales
    NorthEast & Great Lakes Region
    518.410.9404

  3. #23
    Senior Member
    Join Date
    Feb 2010
    Location
    Indianapolis
    Posts
    283

    Default Re: Primer Fuel Line Failure

    I will ask again, what is the correct solution to this serious problem?
    ignore it or talk about thread sealant?

  4. #24
    Senior Member turbopilot's Avatar
    Join Date
    Feb 2010
    Location
    La Quinta, CA
    Posts
    536

    Default Re: Primer Fuel Line Failure

    Quote Originally Posted by seastar View Post
    I will ask again, what is the correct solution to this serious problem?
    ignore it or talk about thread sealant?
    Flexible braided stainless steel fuel line. Running copper fuel lines to a vibrating engine does sound a bit old fashioned.
    Bob Anderson, CC11-00435, N94RA

  5. #25
    Senior Member
    Join Date
    Jul 2015
    Location
    Broken Arrow, OK
    Posts
    841

    Default Re: Primer Fuel Line Failure

    Quote Originally Posted by seastar View Post
    I will ask again, what is the correct solution to this serious problem?
    ignore it or talk about thread sealant?
    Seems like that’s what people are on here doing....trying to help you figure it out. I believe the last post was Mark asking for some photos?
    Dave Embry
    "You only live once.......but if you do it right.........once is enough."..

  6. #26
    Senior Member
    Join Date
    Nov 2013
    Location
    Upstate NY
    Posts
    397

    Default Re: Primer Fuel Line Failure

    Quote Originally Posted by turbopilot View Post
    Running copper fuel lines to a vibrating engine does sound a bit old fashioned.
    That is used on maybe every certified aircraft built, with success

    Glenn

  7. #27
    Senior Member turbopilot's Avatar
    Join Date
    Feb 2010
    Location
    La Quinta, CA
    Posts
    536

    Default Re: Primer Fuel Line Failure

    Quote Originally Posted by Cubdriver2 View Post
    That is used on maybe every certified aircraft built, with success

    Glenn
    Yup all grandfathered. I have owned many new airplanes certified under the newer Part 23 regulations which if I recall happened in the 1970's. I can assure you I have never purchased an airplane certified under new Part 23 with a rigid metal line from the fire wall to the engine. While I understand my CC is not a Part 23 airplane it was built in this century (2014). Makes no sense "today" to make an airplane with a rigid metal tube running from the firewall to the vibrating engine.
    Bob Anderson, CC11-00435, N94RA

  8. #28
    Senior Member
    Join Date
    Nov 2013
    Location
    Upstate NY
    Posts
    397

    Default Re: Primer Fuel Line Failure

    Every airplane I have ever worked on has had a copper primer line. And not only one piece from the firewall but one piece from the primer. My yellow cubs is even longer, I have a swingout mount and a couple extra feet of copper. Only primer problem I ever had in the last 4400hrs happened last fall on a 78 year old floatplane and the primer failed to work. Who ever installed it last must have just tightened it finger tight and the ferrule fell off when it came loose. I know we have better materials today but I still trust time tested simple things that work.

    Glenn

  9. #29
    Senior Member
    Join Date
    Feb 2010
    Location
    Indianapolis
    Posts
    283

    Default Re: Primer Fuel Line Failure

    Thanks for the answers to my question.
    I think I'll go with braided line.
    Don't want to fly a fire ball!
    Good luck Glenn!
    Bill

  10. #30
    Junior Member Firekeeper's Avatar
    Join Date
    Jul 2021
    Location
    UK
    Posts
    3

    Default Re: Primer Fuel Line Failure

    The primer is a fuel pump from the tank to the carburetor chamber. If the liquid does not return, see at what stage and where the discharge occurs in this branch.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •