Page 2 of 5 FirstFirst 12345 LastLast
Results 11 to 20 of 46

Thread: Engine install Questions (Help)

  1. #11
    Senior Member N867SP's Avatar
    Join Date
    Oct 2013
    Location
    Severna Park, MD
    Posts
    342

    Default Re: Engine install Questions (Help)



    I knew I had an actual photo somewhere!


    Pete
    CCK-1865-0078
    ️N9PW
    Severna Park, MD
    Sent from my iPad using Tapatalk
    Pete
    ✈️CCK-1865-0078 N9PW
    Severna Park, MD W18

  2. #12
    Senior Member N867SP's Avatar
    Join Date
    Oct 2013
    Location
    Severna Park, MD
    Posts
    342

    Default Re: Engine install Questions (Help)

    Okay, looked thru inventory sheets, maybe 476-640 in Finish Tote 8?




    Pete
    CCK-1865-0078
    ️N9PW
    Severna Park, MD
    Sent from my iPad using Tapatalk
    Pete
    ✈️CCK-1865-0078 N9PW
    Severna Park, MD W18

  3. #13
    Senior Member c130jake's Avatar
    Join Date
    Jun 2012
    Location
    Minneapolis, MN
    Posts
    190

    Default Re: Engine install Questions (Help)

    I did my own panel with a G3x touch (wasn't available yet from CC) so I am guessing it's not in my kit since the fuel cube was part of the garmin 4cyl kit. I am sure I am in the same boat with the CHT/EGT hardware.

    Anyone finish a kit with the g3x touch yet? If so, what did you use for instructions on the EGT/CHT install and routing? The manual says to check that the EGT doesn't contact the cowl. I checked the Misc folder in drop box and can't find any instructions.

    Thanks again Pete, you are a lifesaver.

    Jake


    Sent from my iPad using Tapatalk
    Jake
    Finished CCEX N96FV!

  4. #14
    Senior Member N867SP's Avatar
    Join Date
    Oct 2013
    Location
    Severna Park, MD
    Posts
    342

    Default Re: Engine install Questions (Help)

    So EGT/CHT is pretty typical and not too dependent on mfg.





    Typically you want to be 1-1/2" to 2" from exhaust port, the CC exhaust has a slight taper as it leaves the exhaust port, just past that it straightened out and it was right in the correct distance. Ideally they all 4 need to be same distance from port. Mine clear the cowl with room to spare. I routed them along starter Caleb and ignition cables, keeping away from ignition pickup wires.


    Pete
    CCK-1865-0078
    ️N9PW
    Severna Park, MD
    Sent from my iPad using Tapatalk
    Pete
    ✈️CCK-1865-0078 N9PW
    Severna Park, MD W18

  5. #15
    Senior Member N867SP's Avatar
    Join Date
    Oct 2013
    Location
    Severna Park, MD
    Posts
    342

    Default Re: Engine install Questions (Help)










    Pete
    CCK-1865-0078
    ️N9PW
    Severna Park, MD
    Sent from my iPad using Tapatalk
    Pete
    ✈️CCK-1865-0078 N9PW
    Severna Park, MD W18

  6. #16
    Senior Member c130jake's Avatar
    Join Date
    Jun 2012
    Location
    Minneapolis, MN
    Posts
    190

    Default Re: Engine install Questions (Help)

    Thanks again Pete!


    Sent from my iPad using Tapatalk
    Jake
    Finished CCEX N96FV!

  7. #17
    Senior Member c130jake's Avatar
    Join Date
    Jun 2012
    Location
    Minneapolis, MN
    Posts
    190

    Default Re: Engine install Questions (Help)

    Another question...I installed the carb heat muff no problems...moved to the cabin heat and the clamps called for in the manual hdw3720. My parts are either wrong or the manual is wrong.



    Sent from my SM-G920V using Tapatalk
    Jake
    Finished CCEX N96FV!

  8. #18
    Senior Member c130jake's Avatar
    Join Date
    Jun 2012
    Location
    Minneapolis, MN
    Posts
    190

    Default Re: Engine install Questions (Help)

    Anyone know where eight 1.75in clamps are used?

    Sent from my SM-G920V using Tapatalk
    Jake
    Finished CCEX N96FV!

  9. #19
    Senior Member Cubrath's Avatar
    Join Date
    Jun 2013
    Location
    Spearfish, SD
    Posts
    302

    Default Re: Engine install Questions (Help)

    Quote Originally Posted by c130jake View Post
    Anyone know where eight 1.75in clamps are used?

    Sent from my SM-G920V using Tapatalk

    Its a trick! You take two clamps and put them together and make one to go around the heat muffs. I called Mitch with the same question! He didn't even know why the engineers chose to do that! So, eight clamps turn into four!

    Mike

  10. #20
    Senior Member c130jake's Avatar
    Join Date
    Jun 2012
    Location
    Minneapolis, MN
    Posts
    190

    Default Re: Engine install Questions (Help)

    I am guessing 58 of the SP50031-001 might incorrect too.

    Sent from my SM-G920V using Tapatalk
    Jake
    Finished CCEX N96FV!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •