Page 24 of 26 FirstFirst 1234567891011121314151617181920212223242526 LastLast
Results 231 to 240 of 252

Thread: Leading Edge Skin Clamps

  1. #231
    Junior Member
    Join Date
    Jul 2018
    Location
    Littleton, CO
    Posts
    7

    Default Re: Leading Edge Skin Clamps

    Drew,
    I'll send them off this week and you can send them to Scott when your done.
    Steve

  2. #232
    Junior Member
    Join Date
    May 2019
    Location
    Fort Worth, TX
    Posts
    7

    Default Re: Leading Edge Skin Clamps

    Quote Originally Posted by stautz View Post
    Drew,
    I'll send them off this week and you can send them to Scott when your done.
    Steve
    Thanks, I probably won't need them until November-ish anyway.

    scott

  3. #233
    Junior Member
    Join Date
    Jan 2014
    Location
    East Lansing, MI
    Posts
    9

    Default Re: Leading Edge Skin Clamps

    Sounds like a plan.

    Thanks

    Quote Originally Posted by stautz View Post
    Drew,
    I'll send them off this week and you can send them to Scott when your done.
    Steve

  4. #234
    Junior Member
    Join Date
    Jul 2018
    Location
    Littleton, CO
    Posts
    7

    Default Re: Leading Edge Skin Clamps

    Drew,
    The clamps are on their way via UPS. Let me know if they don't show up this week and I'll track them.
    Steve

  5. #235
    Junior Member
    Join Date
    Sep 2011
    Location
    Cheyenne, WY
    Posts
    13

    Default Re: Leading Edge Skin Clamps

    Does anyone else have leading edge wing clamps that they may no longer need in the near future? I should be needing them around the November time frame.

    thanks
    chris

  6. #236
    Senior Member
    Join Date
    Jul 2015
    Location
    Broken Arrow, OK
    Posts
    535

    Default Re: Leading Edge Skin Clamps

    FYI. Just thought I’d post this again. I built a number of sets of the clamps and sent them all out. Cubcrafters had originally built 22 sets and they all seemed to “disappear”.

    Mitch asked that kit builders not get clamps until BOTH wings were completed and ready for the leading edge skins and not get them and sit on them.

    It’s easy to build the wing almost complete without the leading edge skins, then set it into the wing holder and then do the other wing. When both are almost ready, then get aa set of clamps, use them and then they can be sent on to someone else. Installing the leading edge skins takes a couple hours at most so no need to get the clamps way in advance.

    I think people are getting the clamps before they even get the kit and then sit on them for a year holding up others who need them.

    I just know how frustrating it is to need a wing clamp and you are unable to get them because they are sitting in someone’s hangar. If everyone would do it this way, no one would get held up.

    Thanks
    Dave Embry
    "You only live once.....
    ..but if you do it right.....
    ....once is enough."..

  7. #237
    Junior Member
    Join Date
    Sep 2011
    Location
    Cheyenne, WY
    Posts
    13

    Default Re: Leading Edge Skin Clamps

    Copy Dave. I wasn’t sure what the build flow would be. Thanks for the feedback.
    chris

  8. #238
    Junior Member
    Join Date
    Oct 2018
    Location
    Idaho
    Posts
    17

    Default Re: Leading Edge Skin Clamps

    I'll be hunting for a set around the end of September first part of October. I'm in Idaho if anyone nearby has a set, please put me on your radar. Thx

    -Marcus

  9. #239
    Junior Member
    Join Date
    Oct 2018
    Location
    Idaho
    Posts
    17

    Default Re: Leading Edge Skin Clamps

    I have both wings ready for leading edge skins. Does anyone have a set of clamps they could send me? I should be able to turn them around in a week or two. I'll pay shipping. I am in Idaho. Thank you!

    -Marcus

  10. #240
    Member N536cs's Avatar
    Join Date
    Aug 2015
    Location
    Santa Maria, CA
    Posts
    34

    Default Re: Leading Edge Skin Clamps

    Quote Originally Posted by PropWash_ID View Post
    I have both wings ready for leading edge skins. Does anyone have a set of clamps they could send me? I should be able to turn them around in a week or two. I'll pay shipping. I am in Idaho. Thank you!

    -Marcus
    We sent our set of leading edge clamps to someone else a year ago. Keep asking around, there should be a set available.

    Scott & Kim.
    Scott and Kim Huntington
    2007 CubCrafters CC11-100 "Sierra"
    2008 CubCrafters CC11-100 "Priscilla"

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •